Automatic Power Buffer 4,700uF 2 wire - for small locos or limited space

Does you loco stall on switches? the Automatic Power Buffer provides UPS Power for your locos decoder for motor, sound, lights, smoke and all other functions when track power is lost.

Direct From Manufacturer - MADE IN THE USA

The 4,700uF capacitor is very small for fitting in small locos or locos with little interior space.

Shourt Line Item No.: SL-6101047

Discount Direct Price: $37.95 NEW

For questions on this item or details on our professional repair, restoration and digital sound decoder installation services Call 310-622-4431 or email us at info@ShourtLine.com

Features:

Easy two wire installation - no switch required. Works with any decoder including all Massoth decoders with or without sound.

• No switch or 3rd wire required for programming your decoder in your loco.
• Automatic Operation with motor, sound or motor/sound decoders
• Easy install to any decoder that has + and - voltage terminals or solder pads
• Works with or without a decoders buffers control outputs
• Small size allows flexible placement in most locomotive
• Installs in minutes

Without the a SL Power Buffer, your loco can stall or jerk and lights flicker or go out on switch frogs, dirty track or dead sections of track. The SL Automatic Gold Cap Buffer eliminates these power interruptions in the same way a UPS (Uninterruptible Power Source) can keep you computer operating when power fails. When your loco passes over the bad track, the buffer continues to supply power to the motor, lights, sound and all other loco features, your loco continues to operate even without track power!

Specifications:

• Works with any decoder including all Massoth decoders with or without sound.
• Size - Small Sealed circuit is 10mm(.4”)H X 13mm(.5”)W X 52mm(2”)L.
• Size -The capacitor is 16.3mm(.64”) Dia. X 38mm(1.5”) L
• 10” power leads to the capacitor and decoder.
• Installs in minutes for decoder UPS power and automatic buffer shutoff when programming your decoder.
• Connect Red wire to decoder + and Black wire to decoder – terminals.
• For MTS, DCC or DC powered decoders or sound boards
• No switch required for programming
• Automatically detects programming and switches off to allow programming (Pat. Pend)
• Maximum charge current is 200 ma (.2 amps)
• Maximum operating voltage 25 Volts DC (from decoder or sound board)
• Maximum track voltage 26 Volts AC or DC
• Operates with DC (analog) or AC, DCC or MTS track power
• Made in the USA by the Shourt Line

Easy Hook-up: Just connect red wire to + and black wire to the plus (+) & minus (-) outputs on your decoder.

Easy Placement: The control circuit and capacitor are separated to allow flexible placement where other power buffers just don't fit. This photo shows a typical loco with no room to fit an LGB power buffer but the Shourt Line power buffer fits easily. Notice the control circuit is in the center of the photo to the right of the Massoth XLS sound decoder and the power buffers capacitor fits nicely in the area to the right.

Automatic controller circuit show above at the top of photo is only .5" wide and .375" high and 2.2" long that fits nicely along side your decoder board or as desired.

Easy to connect to a Massoth L decoder for use in with an LGB direct decoder interface: The red and black wires are soldered as shown above for decoders that have no terminals or pads for the Plus (+24V) and Negative (Gnd) Decoder Outputs.

Massoth L decoder + pre wired Automatic 4,700uf Power Buffer: Order both items from the shourt line (shown above) when you need to install a decoder into a LGB loco with the direct decoder interface and want the advantages of a power buffer for smooth running with or without power shoes.

Avoid stalled locos: Provides power to travel over dead switch frogs or dirty sections of track while sound, lights, motor, smoke and other accessories continue to operate.

For indoor or outdoor use - Pat. Pend. all rights reserved

Questions? Email info@ShourtLine.com by clicking here

Thanks for looking - Shourt Line by Soft Works Ltd.

copyright 2010 ShourtLine.com - Soft Works Ltd. all rights reserved

Pick the size and capacity of your choice: The Automatic Power Buffers are availabel in sizes and capacity for every G-Scale Loco (from top to bottom the buffer above are;

• SL-APB-33000 33,000uF (3X power)
• SL-APB-22000 22,000uF (2X power)
• SL-APB-10000 10,000uF (>1X power)
• SL-APB-8200 8,200uF (1X power = LGB 65011 = Massoth 8865011)
• SL-APB-4400 4,400uF (small loco size)
• SL-APB-3300 3,300 (very small loco size)